Cement Testing Equipments
Vibrating Machine
Max Weight | 200-400 kg |
Power | 4-6 kw |
Voltage | 220V |
Phase | 1 ph |
Dimensions | 950 x 1000 x 1200mm (W x L x H) |
Material | Cast Iron |
Product Type | Vibrating Machine |
Other details:
- Heat of Hydration
- Calorimeter : IS : 4031, BS 4550,ASTM C186for Heat of hydration of Cement. Consists of : A open mouthed thermos flask, Beckman Thermometer, Insulating material, Container, Hinge, Stirring Motor, thermometer support, Glass stirring rod, Cork stopper, Reading Lens and glass Funnel.
- ASEW-152
- Supplied complete with one cube mould 7.06 cms with base plate. Suitable for operation on 230 V, single phase, 50 cycle, A.C. supply Complete with timer.
- VIBRATING MACHINE: IS: 10080, BS 4550 Consists of a frame mounted on coil springs to carry the cube mould , and a revolving shaft provided with an eccentric.
- By means of a balance weight beneath the base plate attached rigidly to the frame, the center of gravity of the whole machine, including the cube and mould, is brought either to the eccentric shaft, or within a distance 25mm below it.
- Normal running speed of eccentric shaft is 12,000±400RPM. Fitted with BELT GUARD. The motor and a crowned pully on the vibration machine.
- Vibrating machine with Digital timer.
- Pocking rod. Spares:
- Belt
- Set of Springs
- Belt guard
- Cube Mould, steel 7.06 cms with base plate
- Time switch 0-5 minute.
Cement Mortar Mixer
Voltage | 220V |
Phase | 1 ph |
Dimensions | 950 x 1000 x 1200mm (W x L x H) |
Power | 3 HP |
Weight (approx.) | 245 kg |
Material | Cast Iron |
Product Type | Mortar Mixer |
Other details:
- ASEW 155
- Scraper-The scraper consists of a semi-rigid rubber blade attached to a handle about 150 mm long. The blade about 75 mm long, 50mm wide and tapered to a thin edge. Suitable for operation on 230volts, single phase, 50 cycle, A.C. supply
- Mortar Mixer (Mixing Apparatus): IS : 4031; IS : 10890, BS 3892
- Mixer Blade Planetary movement Rev/min rev/min
- Low speed 140 ± 5RPM & Plantry 62 ± 5RPM
- Medium speed 285±10RPM& Plantry 125±10
- Stainless steel Bowl fitted with handle. It shall be provided with a lid made of non-absorbing material and not attacked by cement, masonry cement, cement Pozzolana mixture or lime Pozzolana mixture.
- The mould surrounded by the hopper can be clamped rigidly to the table. Supplied complete with mould and hopper. Operation on 230V, single phase, 50 cycle, A.C. Supply.
- Jolting apparatus : IS: 4031 ,IS 10078,BS 3892 The jolting apparatus consists of a rectangular table rigidly connected by two support arms to a spindle at horizontal distance of 800 mm from the center of the table.
- The table can be raised and allowed to fall freely by a com stroke counter fitted with micro-switch is provided which stops the machine after 60 jolts. Locating pins are provided for mounting the mould compartment on the table.
- Soundness of Cement & Hydrated Lime
- ASEW-157
- Le-chatelier mould complete with two glass plate and one lead weight IS: 4031, IS:5514,BS 6463-44.
- Le-Chatelier Flask for Specific Gravity test IS : 4031.
- Le-Chatelier Water Bath with rack for holding Moulds. Fitted with Thermostat.
- Water Retension Test: IS :4031
- Cement Spatula : IS : 269; BS:12 for the preparation of tensile Specimens.
- Gauging Trowel : IS : 4031; BS: 12 fitted with wooden handle.
- Determination Of Strength Of Cement And Mortar
- ASEW-163
- 400 kg (4 Kn) Flexure Testing machine, electrically operated. Complete with flexure attachment. Proving Ring of 400 kg. Capacity. Operation on 230 Volts, single phase, 50 cycle, A.C. supply.
Length Comparator
Material | Cast Iron |
Power | 3 HP |
Voltage | 220V |
Phase | 1 ph |
Dimensions | 950 x 1000 x 1200mm (W x L x H) |
Weight (approx.) | 245 kg |
Product Type | Cement Autoclave |
Other details:
- Determination of Soundness By Means Of Autoclave Test
- ASEW-145
- Length Comparator: IS: 4031 Consists of a frame with adjustable cross plate and a recessed seating and a stainless steel reference bar with 6 mm dia balls mounted at the ends Supplied complete with a dial gauge 0.002 mm.
- Cement Autoclave for a high pressure steam as per IS:4031,ASTMC151.
- Consists of a stainless steel cylinder with an insulated cover. Mounted on a sturdy supporting frame, enclosed in a heat insulating metal housing. The attached control unit enclose a sensitive pressure regulator and pressure gauge, power switches and pilot lamps for controlling the electric heating unit. Inside chamber size; 15 cms dia x 60 cm height.
- Laboratory Cement Autoclave, with Electronic Digital Readout for Pressure & temperature.
- Gauging Trowel
- Fitted with wooden handle.
- Shrinkage bar mould, IS: 10086, IS: 4031,BS 1377 with base plate & two reference points
- Shrinkage bar mould with two mould compartment on a single base.
- Shrinkage Bar mould with three compartment on a single base.
- Shrinkage bar mould with four mould compartment.
Permeability Tester
Material | Cast iron |
High pressure | 5 kg/cm2 to 15 kg/cm2 |
Voltage | 220V |
Phase | 1 ph |
Dimensions | 950 x 1000 x 1200mm (W x L x H) |
Power | 3 HP |
Weight (approx.) | 245 kg |
Product Type | Tester |
Other details:
- ASEW-172
- Permeability Tests: IS : 1727; IS : 1645 : Consists of: Specimen container ring of 100 mm diameter and50 mm high, held between a bottom plate and a water cell. The Water cell of 100 mm diameter brass cylinder and the top and bottom
- Plates of brass or any other non-corroding metal. Each cell with collar is clamped in between a base plate and a top plate with the help of tension rods and nuts.
- The cell assembly is mounted on the stand. The top plate is provided with an inlet and air release vent and the base plate is provided with an outlet. Complete with a pressure chamber is fitted with a pressure, and a pressure gauge 0-10 kg/cm2 indicating the chamber pressure,
- Three Cell Model with Air compressor.
- Six Cell Model with Air compressor.
- Permeability Testers, IS : 3085. Consists of the following
- Permeability Cell-Consists of a metal cylinder with a ledge at the bottom for retaining the specimen, a flange at the top, removable cover plate and a funnel. A rubber or neoprene 0-ring or gasket, seated in matching grooves, between the cell and the cover plate to render the joint water-tight.
- Water Reservoir-Consists of a length of metal pipe, 50 to 100mm in diameter and about 500 mm long. The reservoir fitted with a graduated side arm gauge-glass, and the necessary fitting and valves for admitting water and compressed air and for drainage, bleeding and connection to the permeability cell.
- Pressure Lines Heavy duty armoured rubber hose with end fittings. Complete with glass bottles but without compressor.
- Single Cell Model: for specimen size 100 mm diax 100 mm high
- Three Cell Model: for specimen size 100 mm diax 100 mm high.
- Single Cell Model: for specimen 150 mm dia x 150 mm high.
- Three Cell Model: for specimen 150 mm dia x 150 mm high
- Three Cell Model : for specimen size 150mm cube. Cellmade of Castlron/M.S.
- Three Cell Model: for specimen size 150 mm cube. Cell made of gunmetal.
- Accessories:
- Air Compressor, high pressure 5 kg/cm2 to 15 kg/cm2. fitted with regulating valves pressure gauges and safety valve.
Flow Table
Voltage | 440 V |
Phase | 3 phase |
Power supply | AC Supply |
Material | Cast Iron |
Product Type | Flow Table |
Free fall | 12.5 mm. |
Other details:
- Flow and Workability of Mortars And Lime
- ASEW-182
- Flow Table, Manually operated
- IS:5512.BS:4551-1,ASTMC230
- The Flow Table consists of a brass table top 250±2.5 mm dia mounted on a rigid stand. The table top is re-inforced with equally disposed ribs and allowed to drop through 12 mm by a ground and hardned cam.
- Flow Table, Motorized
- Same as ASEW-182 but cam shaft is rotated at the rate of 100 r.p.m. by an electric motor. Suitable for operation on 230 Volts, 50 cycles, single phase, A.C. Supply.
- Spares:
- Flow Mould.
- Flow of Building Limes
- ASEW-184
- Flow Table: IS 6932 (Part VIII) Consists of a steel table top 300 mm dia ground and polished with three inscribed annular circles 70, 110 and 190 mm dia arranged by cam action have a free fall of 12.5 mm. Complete with conical mould 65mm dia of larger end, 40 mm dia of narrow end and 90 mm high.
Cement Autoclave
Brand | Associated Scientific & Engineering Works |
Capacity | 0-500 (kg/hr) |
Material | Stainless Steel |
Size | 15 cm x 60 cm |
Country of Origin | Made in India |
Product Type | Autoclave |
Grade | Automatic |
Cement Autoclave for a high pressure steam
as per IS: 4031, ASTM C151, AASHTO T107 with Digital temperature Controller.
Uses accelerated means of estimating delayed expansion of Portland cement caused by hydration of CaO and MgO. Test bars are exposed to controlled steam pressure and corresponding constant temperature. Unit produces 60-350 psi (0.4-2.4MPa) range of as pressures and consists of steam vessel, pressure regulator, pressure gauge (0-600 psi x 5 psi), air vent valve, power switches and safety pop valve set at 350psi. includes Digital temperature controller cum indicator, wrench and gasket.
Consists of a stainless steel cylinder with an insulated cover. Mounted on a sturdy supporting frame, enclosed in a heat insulating metal housing. . Inside chamber size; 15 cms dia x 60 cm height.